Range 01
Foam-backed and felt-backed rolls from 1.0 mm to 4.0 mm, 1,100 to 2,300 g/m². For apartments, rentals, homestays, clinics and light offices — laid loose, glued, or taped at the seam.
01 — The range
Everything on this page is residential sheet vinyl, sold by the roll. The question is not which decor — it is which back.
Foamed & coated gives you thickness: 1.6 to 4.0 mm of chemically foamed vinyl that cushions footsteps and bridges small dips in the subfloor.
PVC-coated felt gives you a thinner, denser roll: 1.0 to 2.3 mm on a needle-punch felt core, dimensionally stable and good where a door has to clear the floor.
02 — Constructions
Same print film, different body. Both are 2 m wide and cut to the roll length you order.
QC-F · FOAMED & COATED
Chemically foamed middle layer, coated surface. The workhorse for homes, rentals and light commercial floors.
QC-M · PVC-COATED FELT
Needle-punch felt core coated with PVC. Thin, stable and anti-slip — the specification most buyers pick for renovation work.
03 — Specification
Thickness and weight as produced, not as rounded for a brochure. Ask for the technical sheet of the step you intend to order.
| Thickness | Weight | kg per m² | Typical use |
|---|---|---|---|
| 1.6 mm | 1,100 g/m² | 1.1 kg/m² | Living room, rental, office |
| 1.8 mm | 1,200 g/m² | 1.2 kg/m² | Living room, rental, office |
| 2.0 mm | 1,300 g/m² | 1.3 kg/m² | Living room, rental, office |
| 2.5 mm | 1,500 g/m² | 1.5 kg/m² | Stairs, hallway, light traffic |
| 2.8 mm | 1,700 g/m² | 1.7 kg/m² | Stairs, hallway, light traffic |
| 3.0 mm | 1,800 g/m² | 1.8 kg/m² | Stairs, hallway, light traffic |
| 4.0 mm | 2,300 g/m² | 2.3 kg/m² | Heavy traffic, shop floor |
| Construction | Thickness | Weight | kg per m² |
|---|---|---|---|
| 130 g PVC coated felt | 1.0–1.1 mm | 1,100 g/m² | 1.10 kg/m² |
| 150 g PVC coated felt | 1.1–1.3 mm | 1,200 g/m² | 1.20 kg/m² |
| 180 g white, matte film | 1.3–1.4 mm | 1,350 g/m² | 1.35 kg/m² |
| 180 g black, matte film | 1.3–1.4 mm | 1,500 g/m² | 1.50 kg/m² |
| 200 g white, matte film | 1.5–1.6 mm | 1,500 g/m² | 1.50 kg/m² |
| 250 g white, matte film | 1.8–2.0 mm | 1,500 g/m² | 1.50 kg/m² |
| 200 g blue, matte film | 1.5–1.6 mm | 1,500 g/m² | 1.50 kg/m² |
| 250 g blue, matte film | 1.8–2.0 mm | 1,500 g/m² | 1.50 kg/m² |
| 300 g white, matte film | 2.1–2.3 mm | 1,700 g/m² | 1.70 kg/m² |
| 300 g black, matte film | 2.1–2.3 mm | 1,700 g/m² | 1.70 kg/m² |
Roll width 2 m as standard; other widths on request. Minimum order, packing and lead time are quoted per order — tell us the quantity and destination port.
04 — Decors
Every one of the 648 runs on the same 2 m wide film, so you can mix a wood in the living room with a terrazzo in the bathroom without changing construction. Codes are the ones we quote against.
Plank
Plank
Plank
Plank
Plank
Plank
Plank
Plank
Plank
Plank
Terrazzo
Terrazzo
Terrazzo
Terrazzo
Terrazzo
Terrazzo
These are the eight we show most; the full range of 648 is in the decor library. Other prints can be run on request — send us a photo or a sample.
05 — On site
This is not a plank floor. The roll is cut to the length of the room, carried in, unrolled and left to relax — the whole floor goes down in one piece, so there is no grid of joints to collect dirt, lift at the edge or telegraph through.
Fitters trim it at the wall with a knife in a single pass, tuck the edge under the skirting, and weld only where the room is wider than the 2 m roll. A bedroom, a corridor or a small shop usually needs no seam at all.
Short version below. The full sheet goes in the carton.
Subfloor. Sweep, fill and let it dry. Foam back bridges 1–2 mm of unevenness; anything deeper will telegraph through within a season.
Unroll and relax. Carry the roll in, unroll it face up and leave it flat for a day. Cold vinyl is stiff vinyl — it will not sit down, and it will pull back after trimming.
Trim at the wall. Rough-cut 50 mm oversize, press the sheet into the corner, then cut flush with a sharp blade held against the wall. Skirting or a coving strip hides the last 20 mm.
Seam only if you must. Where the room is wider than 2 m: overlap, double-cut through both layers, weld with rod and trim flush. Loose-laid work can be taped instead.
06 — Questions
07 — Next step
Send the thickness, the decor code and the roll length you need — or just describe the project and we will propose a construction.
